Strongcoat HB
Previous product
Next product
Strongcoat WD
 

Strongcoat
SL

SELF-LEVELLING EPOXY TOPPING FOR FLOOR SURFACES
 


Strongcoat SL is a three-pack solvent free, epoxy-based selflevelling topping that provides floor surfaces with a seamless, hygienic and cosmetically attractive finish.

Usage

Strongcoat SL is applied by trowel to horizontal surfaces and has very good durability towards pedestrian and vehicular traffic. It also has very good resistance to many of the chemicals commonly found in an industrial environment (consult our Technical Department for further details). It can be supplied in a variety of colours (consult our Sales Department for details). Slip resistant finishes can be produced for very demanding situations.

KIT FORM

18kg

THICKNESS RANGE

3-6mm

COVERAGE

Approximately 3.5m² per kit at 3mm thick.

STORAGE

Store at temperatures between 5°C and 30°C.

SHELF LIFE

Approximately 24 months if stored in unopened containers and under good conditions.

SURFACE PREPARATION

The surface must be clean, dry (less than 75% RH measured by hygrometer) and free from dust, laitance, oils, paints or other forms of contamination. Grit blasting can be used to remove laitance and surface contamination (see the Guide to Surface Preparation for further details). For treatment of surfaces containing expansion joints consult our Technical Department.

Technical Information

EN 13813 Designation
SR-ARO,5-B2,0-IR10
Wear Resistance
(EN 13892-4)
≤50 μm
Bond Strength
(EN 13892-8)
≥ 2.0 N/mm²
Impact Resistance
(EN ISO 6272-1)
≥ 10 Nm

Application Instructions

PRIMING
Surfaces must be primed with Strongcoat Primer prior to application of Strongcoat SL (see the Strongcoat Primer Data Sheet for further details).

• More than one coat of Strongcoat Primer may be required for highly porous or textured surfaces.

MIXING
Taking care to ensure that the bottom and sides are thoroughly scraped, transfer the entire contents of both the Resin and Hardener into a separate mixing container. Using a jiffy-type mixer attached to a slow-running electric drill, mix for approximately two minutes. Once the Strongcoat SL Hardener and Resin have been mixed, transfer the entire contents of the Resin container into a Casco or Creteangle-type mixer, taking care to ensure that the bottom and sides are thoroughly scraped. Start the mixer and transfer to it the entire contents of the Strongcoat SL Filler container, taking care to ensure that these are completely dry and lump-free. Continue mixing for approximately two minutes.

• Never mix Strongcoat SL by hand as this could lead to areas of uncured material.

APPLICATION
Once mixing is complete, transfer the Strongcoat SL to the primed surface and, using a straight-edged steel trowel, apply it evenly.

WORKING TIME
Approximately 15 minutes at 20°C.

• Never leave the mixed Strongcoat SL kit to stand for any length of time prior to application as this will considerably shorten its working time.

FINISHING
Whilst still wet, thoroughly spike roll the Strongcoat SL.

CLEANING
Once mixing, application and finishing are complete, tools can be cleaned with a suitable solvent.

CURING TIME
At 20°C Strongcoat SL should be allowed to cure for 48 hours prior to opening it to pedestrian traffic. At the same temperature, it should be allowed to cure for seven days prior to opening it to vehicular traffic or exposing it to chemical contamination (consult Technical for details of curing times at other temperatures).




Download file



Related products




How to





Connect with Don Construction Products


Name *
Email *
Phone
Address
Reason
Request  
Security Code *
Don Construction Products Bulgaria EAD

Sales office

Monday - Friday: 9:00 - 17:30

Sofia 1582, Bulgaria
152 Prof. Tsvetan Lazarov blvd.
Techno Park Sofia
Tel.: +359 2 870 2782; +359 2 870 2761

info.bulgaria@dcp-int.com

Technical support

+359 2 870 27 82

Contact form

Get Contact Form