TIBMIX 500
Предишен продукт
Следващ продукт
Setseal 6
 

TIBMIX 700

PRE-BLENDED QUARTZ/CORUNDUM BASED DRY SHAKE FLOOR TOPPING
 

Advantages:

  • Outstanding Abrasion Resistance

  • Very High Compressive Strength

  • Slip Resistance

Description:

TIBMIX 700 is a quartz/corundum based, dry shake floor topping for monolithic floors. The product contains a blend of specially graded aggregates, additives and Portland Cements.

TIBMIX 700 can also be used to suppress steel fibres in concrete floors.

Usage

When trowelled into freshly laid concrete, TIBMIX 700 produces a dense, tough, abrasion resistant surface suitable for most industrial floors. The product is designed for application either by hand or using automatic spreading equipment.

Abrasion resistance conforms to BS EN 13892-4 AR0,5 (Special Class). 

TIBMIX 700 should be used in conjunction with Setseal 6 polymer curing membrane/sealer/hardener.

Coloured versions of TIBMIX 700 are also available which contain a high quality, durable pigment.

Materials Supplied

25kg polythene-lined paper sacks 

Coverage

Recommended application rate of 3-5 kg/m² depending on application - please contact our Technical Department.

Storage

Store under cover, in unopened bags clear of the ground in cool dry conditions, protected from frost and excessive draught.When stored as above, and used within 12 months of the date shown on the packaging, the activity of the reducing agent added will be maintained and the mixed product will contain no more than 0.0002% (2ppm) soluble chromium (VI) on the total dry weight of the cement.

Shelf Life

12 months in unopened bags stored under good conditions.

Standard

  • EN 13813:2002

Technical Information

BS EN 13813 Designation

CT-C70-F6-AR0,5

Compressive Strength (N/mm2)
BS EN 13892-2; 28 Days

> 80,0

Flexural Strength (N/mm2)
BS EN 13892-2; 28 Days

> 7,0

Abrasion resistance 
BS EN 13892-4
AR0,5
Special Class
Slip resistance
BS EN 13036-4
88 Dry
41 Wet
BRE Screed Test
0.7 mm

Application Instructions

BASE CONCRETE

The base concrete should be a minimum grade C30/37 with a cement content no less than 325 Kg/m3 and should be placed in accordance with good concrete practice. The water:cement ratio should be maximum 0,55 and kept to the minimum needed to produce a fully compacted concrete without excess surface water. Should free water be present at the surface this should be allowed to evaporate or brushed away, before the application of TIBMIX 700.

APPLICATION

Broadcast the TIBMIX 700 evenly over the surface of the base concrete. Where manual troweling is involved, application in two stages is recommended. The first stage should be to apply two thirds of the coverage rate of TIBMIX 700 following removal or evaporation of surface bleed water. Immediately after this stage TIBMIX 700 should be troweled in, either by hand or using a power float (pan fitted to blades). Stage two is to apply the remainder of the coverage rate and to repeat troweling. For large floor constructions TIBMIX 700 can be spread and troweled satisfactorily in one stage by mechanical means. When the surface has sufficiently stiffened (usually about two hours from the first troweling), a second troweling should be carried out to close any pores and remove surface undulations. Further treatment may be necessary to remove disc marks and to achieve the final finish required.

CLEANING/WORKING CONDITIONS

All equipment and tools should be rinsed with water immediately after use and then dried.

CURING, HARDENING & SEALING

After final troweling is complete, Setseal 6 (see appropriate data sheet) should be applied by spray taking care to avoid any puddling. Appropriate measures must be taken to prevent the surface from drying out too rapidly. The use of polythene sheeting is not recommended as this can cause blooming of the surface, particularly with colored TIBMIX 700.

JOINTS

Floor expansion joints should be formed using Flexseal PU440 polyurethane joint sealant.


Изтегли файл



Свързани продукти




Как се прави





Връзка с Don Construction Products


Име *
Е-Мейл *
Телефон
Адрес
Причина
Съобщение  
Сигурност *
Дон Констракшън Продуктс 
България ЕАД

Централен офис

Понеделник - Петък: 9:00 - 18:00

София 1582, България
Проф. Цветан Лазаров 152
Техно Парк София, ет.3
Факс: +359 2 870 2761
Тел.:   +359 2 870 2782

info.bulgaria@dcp-int.com

Въпроси за продукти

+359 2 870 2782

Форма

Кликни тук