TIBMIX 700
Предишен продукт
Следващ продукт
Setseal A
 

Setseal
6

ACRYLIC RESIN BASED, CURING AID, SEALER, DUSTPROOFER AND HARDENER
 
Setseal 6 is a clear, acrylic resin based, single pack solution designed to impregnate concrete surfaces combining the benefits of a curing aid, sealer, dustproofer and hardener. 

Usage

Setseal 6 has been designed to overcome the drawbacks of many commonly used curing membranes which tend to provide a limited service life following the curing period of new concrete. It has good abrasion resistance and can be coated with certain coatings (please contact our Technical Department for specific applications).

Materials Supplied

18, 25 and 200 litres.

Storage


Store in closed containers above freezing (0°C) under dry, wellventilated warehouse conditions out of direct sunlight and away from naked flames or other sources of ignition.

Shelf Life

At least 12 months if stored in original containers

Coverage


5 - 12m² per litre per coat depending on the absorbency of the base.

Technical Information

BS EN 13813 CLASSSR-B1,5
AppearanceClear liquid
Curing efficiency75% at 6m² per litre
Drying time at 20°C

Tack-free 4 hours
Hard dry 24 hours
Flash point40°C
Bond strength
(BS EN 13892-8)
1.5N/mm²
Application temperature range5°C to 30°C

Application Instructions

SURFACE PREPARATION 

New concrete 

Setseal 6 should be applied immediately following power floating/finishing of the concrete surface ensuring all excess surface water has evaporated prior to application of the Setseal 6.

Old concrete 

All surfaces must be clean, dry and free from oil and other such contaminants.

MIXING 

Stir the Setseal 6 before use. 

APPLICATION 

New concrete 

Apply Setseal 6 by fine spray at a rate of 5 to 12 m² per litre. In severe drying conditions a second coat should be applied after 2 to 3 hours. Care should be taken to ensure complete coverage.

Old concrete 

Apply Setseal 6 by squeegee, brush, spray or broom at a nominal rate of 5 to 10 m² per litre for the first coat, followed 5 to 8 hours afterwards by a second coat of 10 to 12 m² per litre.

As the  condition and therefore the porosity of concrete surfaces can differ so widely, it is recommended that a test application area be carried out to determine the precise coverage rate for each specific job.

OVERCOATING 

Please contact our Technical Department for specific applications.

WORKING CONDITIONS 

Application range 5°C to 30°C. 
Do not apply in external situations where rain is likely to come into contact with the uncured Setseal 6.

CLEANING 

All equipment and tools should be cleaned thoroughly with Xylene and allowed to dry 

HEALTH & SAFETY 

Consult the appropriate Material Safety Data Sheet before using Setseal 6. 

GENERAL GUIDANCE 

This data sheet is for general guidance purposes only and may contain information that is inappropriate for certain conditions of use. Accordingly, all recommendations and suggestions are made without guarantee. Further information is available from our Technical Department.



Изтегли файл



Свързани продукти




Как се прави





Връзка с Don Construction Products


Име *
Е-Мейл *
Телефон
Адрес
Причина
Съобщение  
Сигурност *
Дон Констракшън Продуктс 
България ЕАД

Централен офис

Понеделник - Петък: 9:00 - 18:00

София 1582, България
Проф. Цветан Лазаров 152
Техно Парк София, ет.3
Факс: +359 2 870 2761
Тел.:   +359 2 870 2782

info.bulgaria@dcp-int.com

Въпроси за продукти

+359 2 870 2782

Форма

Кликни тук