Repelicone
W

WATER-BASED REPELLENT COATING 
 
Advantages:
  • Good penetration into substrate

  • Good reduction of water and chloride intrusion

  • Excellent resistance to alkalis and UV light

  • Minimizes efflorescence

  • Breathable

  • Very good resistance to dust and dirt pick-up

Description:

Repelicone W is a water based, ready for use, single component, water repellent impregnation for application on vertical or steeply sloping concrete, mineral-based natural and artificial stone, cementitious substrates, mineral plasters and mineral paints.


Usage


Repelicone W provides excellent water repellency and protection from weathering to vertical or steeply sloping concrete, mineral-based and artificial stone, cementitious substrates and mineral paints.
Repelicone W can also be used for injection into walls to prevent rising damp.
Repelicone W can be used as moisture barrier primer that is recoatable with water and solvent borne paints.

Materials Supplied

Repelicone W is available in  pails - 1 l, 5 l, 20 l and drums - 200 l.

Coverage


Approximately, depending on substrate0.1- 0.4 l / m2

Storage/ Shelf Life

Repelicone W should be stored under cover at a minimum ambient temperature of 5°C.
Repelicone W has a shelf life of 12 months from date of manufacture if stored in proper conditions and sealed drums.

Remarks

Repelicone W should not be applied when rain is forecasted within 24 hours. Wait at least 24 hours after rain or water cleaning.

Be sure that impregnated surfaces by Repelicone W are not exposed to water and rain for at least 12 hours after application.

DO NOT USE DETERGENTS for cleaning impregnated surfaces by Repelicone W, washing occurs only by water.

Standard

  • EN 1504-2

Technical Information

Density
1.00 g/cm³
Penetration
EN 14630:2007

≥ 5 mm

Measurement of bond strength
EN 1542:2005
≥ 1.5 N/mm2
Liquid water permeability
EN 1062-3:2008
< 0.1
Alkali resistance
EN 13580:2007
< 10%
Water absorption
EN 13580:2007
< 7%
Drying rate coefficient
EN 13579:2003
> 30%
pH
7.8

The technical data are specified at 23 °C.

Application Information

SUBSTRATE PREPARATION

Surface must be clean, sound and free from oil, grease, curing compound, or any contamination. Any contaminants should be removed by light grit blasting. Water jets is then used as the end step of substrate cleaning.   

Note:

Avoid the use of acidic or alkaline chemical detergents and cationic surfactants. If detergents are used for cleaning, it is necessary to rinse well the cleaned surface by water in order to remove any detergent residue.

APPLICATION

It is recommended to apply two consecutive coats of Repelicone W at the stated rate of application, or one flood coat.

Impregnation can be carried out using airless spray machine, brush, or roller.

The water repellent properties fully develop in approximately 72 hours @ 25 °C.

CLEANING

Tools and equipment can be cleaned with water when wet.

HEALTH & SAFETY 

Care should be taken during use and storage to avoid contact with skin, eyes and mouth. Wear suitable protective clothing, gloves and eye/face protection. Should accidental skin contact occur, remove immediately with plenty of clean water. If swallowed, seek medical attention immediately - do not induce vomiting.

For further  information refer to the Material Safety Data Sheet.

FIRE 

Repelicone W is non-flammable.




Download file



Related products




How to





Connect with Don Construction Products


Name *
Email *
Phone
Address
Reason
Request  
Security Code *
Don Construction Products Bulgaria EAD

Sales office

Monday - Friday: 9:00 - 18:00

Sofia 1582, Bulgaria
152 Prof. Tsvetan Lazarov blvd.
Techno Park Sofia
Fax: +359 2 870 2761
Tel.:   +359 2 870 2782

info.bulgaria@dcp-int.com

Technical support

+359 2 870 27 82

Contact form

Get Contact Form