Proplast Acrylic
Previous product
Next product
Grundix Silicate Primer
 

Proplast
Silicate

SILICATE BASED DECORATIVE COAT FOR INTERNAL AND EXTERNAL APPLICATION
 

Advantages:

  • Hydrophobic

  • Weather resistant

  • Highly vapour permeable allowing substrates to breath

  • Good thermal characteristics

  • Variety of decorative textured finishes and colors

  • Easily cleaned
  • Environment friendly

Description:

Proplast Silicate is a highly breathable ready to use, thin-layer decorative plaster for internal and external applications.

Usage


Proplast Silicate consists of a unique composition of silicate binder, mineral fillers, polymers and pigments that provides a superb quality decorative plaster that can be easily applied by trowel for finishing new construction as well as the restoration of cultural heritage building.

Proplast Silicate is available in wide range of attractive colors and textures that provide a uniform and stable decorative appearance on all concrete and cement based substrates.

Proplast Silicate creates a decorative textured finishing on building.
Proplast Silicate is a final layer of the External Thermal Insulation Composite System (ETICS) from DCP
 

Materials Supplied

Proplast Silicate is available in 10 kg buckets and 25 kg pails.

Coverage



Structure Type
Min. thickness,
mm
Theoretical consumption
(kg/ m²)
T0.50.5 - 1.00.8 - 1.6
T1.00.7 - 1.21.2 - 2.0
T1.51.5 - 2.12.6 - 3.7
T2.02.0 - 2.53.3 - 4.1
T3.02.5 - 3.04.3 - 5.2
S2.02.0 - 2.53.4 - 4.3
S3.02.5 - 3.04.3 - 5.1

Storage

Store in original closed containers, in a shaded place at a temperature of 25°C and control conditions

Shelf Life

Proplast Silicate has  6 months shelf life from date of manufacture.

Standard


  • ETAG - 004 (EOTA)
  • EN 15824

Technical Information

AppearancePasty liquid with different grain sizes
Density
EN 1015
1.7 kg/m3
Adhesion on substrate
EN 1542
EN 15824
Liquid water permeability
EN 1062-3
W 2 - average
EN 15824
Water vapour transmission rate - V
EN ISO 7783-2
Cat. V2
EN 15824
pH10
Thermal conductivity coefficient
EN 1745 Table A.12
0.75 W/m.K

VOC
≤ 40 g/ l

Application Information

SUBSTRATE PREPARATION

Surfaces shall be sound, dry and clean from all contaminants. Lightly abrade the substrate using mesh 60 grade sand paper to remove laitence.

Note:

The application of this system is not suitable on gypsum based plaster, plastic and resin paints, varnish and oil-based paints, old water based paint and lime paint.

PRIMING

Prime the substrate using Grundix Silicate Primer by roller, soft brush or airless spray machine at rate of 5 m2 per ltr. For optimum bonding between the substrate and Proplast Silicate and to balance the pH between them, it is recommended to apply a layer of Proplast Universal Primer at a rate of 5 - 8 m2 per ltr using a short hair lamb wool roller or brush. Proplast Universal Primer also helps in the uniformity of the color of the final coat.

After priming, at least 24 hours are needed before applying Proplast Silicate.

APPLICATION

Before the application, Proplast Silicate shall be thoroughly stirred using a slow speed agitator. The material is applied with a stainless steel trowel. Different textures are obtained especially if a floating trowel is used where the working action can be done in circles, horizontally or vertically.

Product Grades and Textures

Proplast Silicate comes with two different systems which is related to the final desired finish.


T type: is the normal textured uniform system; where the largest grain size appears uniformally on the whole finish. The T type comes with different large grain sizes which reflects in the final thickness.
S type: is the scratch type finish, where a selected large grain particles will be spreaded in the finish and gives a randomly scratch effect on the finish. The size of these large grains effect on the thickness of the applied layer.

To overcoat Proplast Silicate use either Procoat Silicate or Procoat Silicone protective coatings as per recommendations of respective technical data sheets.

CLEANING

All tools should be cleaned immediately after finishing using clean water.

HEALTH & SAFETY 

In case of accidental contact with eyes, immediately flush with plenty of water for at least 10 minutes and seek medical advise if necessary.

FIRE 

Proplast Silicate is nonflammable.




Download file



Related products




How to





Connect with Don Construction Products


Name *
Email *
Phone
Address
Reason
Request  
Security Code *
Don Construction Products Bulgaria EAD

Sales office

Monday - Friday: 9:00 - 18:00

Sofia 1582, Bulgaria
152 Prof. Tsvetan Lazarov blvd.
Techno Park Sofia
Fax: +359 2 870 2761
Tel.:   +359 2 870 2782

info.bulgaria@dcp-int.com

Technical support

+359 2 870 27 82

Contact form

Get Contact Form